Search Results for ‘shaft’

Hi all I have A 2007 1.9 diesel estate 9.3 Vacuum pump removed and link shattered. So got a new one. Then realised the ring it joins to on the end of the camshaft has sheared off... I am struggling to find a part number for the sprocket I think it's attached too.. unless it comes separate?? Any...

The steering wheel in my 94 900 S convertible moves up and down because the upper bearing in the steering column is shot. The column assembly is not available new. I could probably find a replacement bearing if I was able to get the column apart. This is a common problem and I would like to hear...

Guys, Mrs P @ K's '02 Cabrio recently died about 10 miles from home. Thinking it was a duff battery or alternator I went on a recovery trip to get it going again. Started straight away with a jump from the Aero battlewagon and swapped cars so I could take it home. Now the strangeness starts...

Hi, I'm hoping somebody may be able to help with advice. My 2.3 has developed a noise clearly audible when sitting inside the car. I think it's coming from the intake side of the engine. The noise is constant, whirring and has an occasional occillation. It has a light rumble to. There's no...

I am trying to hunt down an idler/ jack shaft for my 1977 99 ems. I believe the part # is 8358509. Please pm or email me at maarlen at gmail. com

My Saab was showing some of the classic symptoms of a power steering pump shaft seal going bad, weeping around the filler cap and brown p/s oil instead of green. The replacement of the pump shaft seal is very easy and painless. If you can change your own engine oil, you are fully qualified to...

I have a 97 saab 900 se turbo, 5-speed manual, and it is stuck in second gear. I'm trying to remove the gear box and I've taken everything off, all the bolts, but i cannot get the intermediate shaft to come out. I have tried prying, banging, raising, lowering, everything i can think of but it...

Brand new, boxed in original Saab box, unused Saab jackshaft for Saab 99 turbo. Last time I looked these cost over £500 from Saab - but that's academic because they are no longer available new from Saab. Saab 99 idler shaft (jackshaft), Saab part number: 8358509 Now extremely rare / impossible...

16v 1.9 tid 93 2007 Changing the Timing belt and water pump, Put on my own marks, and all seemed well until whilst Replacing the pump, I got distracted and Turned the camshaft pulley, Not sure how times around. I have lined it the marks up but as the Pump, the drive shaft and the camshaft...

Hi. Can anyone help with a GM part number for the crankshaft oil seal for a 19dth engine in a 2007 93 150 vector sport estate. And also any other possible causes of oil leak in that region of engine, Going to do Timing belt tonight and two GM garages nearby... neither can find part number on...

The car has been great but on Sunday it died. I'm told by the garage that the crank shaft has snapped. The car has done just over 110 000 miles. A brand new turbo was fitted 15k ago. Every thing was working ok on the car before the car died. The car has a tow bar with twin electrics. I...

My trans has been leaking for ever so i went and bought some uv dye and it saw that it was coming from the intermediate shaft im guessing it s the seal. I was wondering if this would be a hard job to do and Im having a hard time see reading this diagram. I cant tell if there's inner and outer...

Hi Guys Does anyone know if it is possible to install a drive shaft from my old 98 9-5 2.0t Auto that has a problem motor but nice quiet drive shafts and put it on my 05 9-5 2.0t Auto that has a nice quiet engine but RHD drive shaft ticks away like mad when I pull off with any lock on (it is ok...

Hi, Performed the self check and got code 1 - 11, RHS shaft broken I believe. Ordered the repair kit and spent an intimate hour under the dashboard to find the shaft still intact. Am thinking it must be the servo motor as the flap worked manually providing both hot and cool air. Servo motor...

Hi, I started getting severe vibration from my 9-5 2.2 tid front wheels. The problem was traced to the fact that the grease had leaked out of the drive shaft inner boot. I managed to pull the boot back and replenish the joint with CV grease. This cured the problem. However it still leaks. I...

Hi, folks. 9000 1997 2.3 lpt. I am running out of the time that I can use a borrowed garage. ( Not an engineering garage ). My prob: an inlet balance shaft gear wheel that I can't separate from the balance shaft. The wheel is knackered, so I can't just leave it in. My questions: how easy is it...

Hi all, I have a knocking noise when doing right hand turns on full lock. I assume this is the left front drive shaft. Question is how difficult are they to remove? And get back in. and what tools am i going to need? Ball joint seperator? Gear puller? i have a big box of sockets, i dont...

Does anyone have any guidance on replacing the entire drive shaft assemblies on a 2002 9-3 (hatchback)? My concern is removing the shaft from the gearbox. Any help would be much appreciated.

Hi, I'm wondering if someone can tell me to which pin on bulkhead connector block does the crank shaft sensor connect? I've been told its an orange wire but there are several. I have code P0335 and am trying to determine if there is a break in the wire as I believe P0336 is the sensor itself...

I have an oil leak from the left hand driver housing area. I am not sure whether it is the drive shaft seal or the "O" ring seal inside the housing cover. Since to replace either (or both)seals, the inner drive shaft and cover has to be removed, I have decided to replace both. I am also...