Saabscene Saab Forum - Saab Technical Information Resource banner
joint
1-20 of 73 Results
  1. Part number requests
    Does anyone know the part number for the pinch bolt that connects the front wishbone/ lower control arm ball joint to the hub? I am going to be changing both wishbones soon and the Haynes manual says you must not re-use the bolt
  2. Help, Advice, Saabs and Motoring
    Does anyone know if the allan set screws on the square hole fitting of the below picture (the allan screw holes are hidden in the photo) are supposed to be there to lock it to the shaft as mine doesn't have any screws in, it has the threaded holes but no screws and I see other post say theirs...
  3. Classic Saab 9-3/GM900 (1994 - 2002)/Conv ( -2003)
    Hi Does anyone know if there two part are the same. I have a 2002 - 93 convertible and need this joint. I have the gold one fitted but they are hard to get hold of but the black ones is available. But will it fit...... .
  4. Current model range, FOR SALE and WANTED
    my saab 2006 93 1.9tid vector im in need of a universal joint so ive been told can someone point me in the right direction please
  5. Saab 9-3 Sedan/Combi/TurboX/AWD(2003+)/Conv(2004+)
    my saab 2006 93 1.9tid vector im in need of a universal joint so ive been told can someone point me in the right direction please
  6. Classic Saab 9-3/GM900 (1994 - 2002)/Conv ( -2003)
    This isn't right is it? There shouldn't be that much vertical movement in the inner CV joint should there? I started getting a vibration from 50kmh up then it became worse. It happened suddenly.
  7. Saab 9-3 Sedan/Combi/TurboX/AWD(2003+)/Conv(2004+)
    Evening all, I have a 2009 ttid estate, 81k. I've got steering wheel wobble at all speeds (particularly low speeds), definitely not vibration... It's a wobble of about 1-2 CM each way constantly & car wants to pull left to an extent. It feels a bit like "tram lining" but to a lesses extent of...
  8. Saab 9-3 Sedan/Combi/TurboX/AWD(2003+)/Conv(2004+)
    Hello to all I've got a new problem. This evening, whilst gently reversing out of my driveway as it's done for years, when I went to move forward, absolutely nothing happened. At first I thought that it must have been either gearbox or clutch related, as there had been no noise between...
  9. Saab 9-3 Sedan/Combi/TurboX/AWD(2003+)/Conv(2004+)
    Has anyone tried one of these? http://www.ebay.co.uk/itm/saab-9-3-TiD-exhaust-flexi-flex-cat-repair-pipe-1-9-TiD-stainless-steel-/111083884879?pt=UK_CarsParts_Vehicles_CarParts_SM&fits=Car+Make%3ASaab|Cars+Type%3A1.9+TiD|Model%3A9-3&hash=item19dd1d914f Mine is blowing and this looks like the...
  10. Classic Saab 9-5 (1997 - 2009)
    Hi all, I am trying to replace a cv joint on my wife's 2002 aero,as the reluctor ring has split and is causing a pulsing when braking. My problem is parting the old joint from the driveshaft.I was expecting a normal circlip,but when I looked at the new parts, they contain a spring clip of some...
  11. Classic Saab 9-5 (1997 - 2009)
    i think i have a failed Inner CV joint Passenger side but im not completely sure :confused: there is a constant noise that is road speed related which gets louder/ more high pitched around right hand corners and quieter around left hand corners starts to be audible over the engine at around...
  12. Saab 9-3 Sedan/Combi/TurboX/AWD(2003+)/Conv(2004+)
    would one from a 9-3 ss 2005 1800 petrol fit a aero 2003 9-3 ss ?
  13. Saab 9-3 Sedan/Combi/TurboX/AWD(2003+)/Conv(2004+)
    hi all, i was changing the wheel bearing on my 9-3 ss, couldnt get the driveshaft out the hub so used a heavy hammer, in doing this the inner cv joint bearing has came appart, ive tried for ages to put the 5 ball bearing back into the unit but keeps popping out, anyone got any ideas how i can do...
  14. Saab 9-3 Sedan/Combi/TurboX/AWD(2003+)/Conv(2004+)
    Hi Guys, my 9-3 150BHP TID has a clunking on full lock on right hand corners. I am guessing that i need to replace my CV joint. Has anyone done this or got any tips? It seems like there are inner and outer joints. http://www.jandrcvjoints.co.uk/saab/cv-joi...ds-p-10175.html Found this...
  15. Classic Saab 900 (1979 - 1993)
    So I did the driver's side cv boot over the course of the past week, and when reassembling instead of putting the circlip in the cv joint and spreading it and putting the axel through, as I should have, I instead put the circlip on the axel and tried to shove the reassembled cv joint over the...
  16. Saab 9-3 Sedan/Combi/TurboX/AWD(2003+)/Conv(2004+)
    Hi all, I have a knocking noise when doing right hand turns on full lock. I assume this is the left front drive shaft. Question is how difficult are they to remove? And get back in. and what tools am i going to need? Ball joint seperator? Gear puller? i have a big box of sockets, i dont...
  17. Saab 9-3 Sedan/Combi/TurboX/AWD(2003+)/Conv(2004+)
    Hi, My dealer says need to get my steering column knuckle joint replaced. I can get a second hand part but I need to know which colour it is and the garage would have to take it in again and strip it to find out. Does anyone know what colour it would be for a 2006 2.0 Aero petrol?
  18. Saab 9-3 Sedan/Combi/TurboX/AWD(2003+)/Conv(2004+)
    Hello, Just noticed my steering getting a bit stiff occasionally even though my power steering fluid is ok. Hopefully not the PS pump but feels like the universal joint in the steering column is seizing. If I try to free it off and lube it up but it doesn't work, I just wondered if anyone knew...
  19. Classic Saab 9-3/GM900 (1994 - 2002)/Conv ( -2003)
    Anyone out there had to change the exhaust section with the flexi joint and cat? Kwik Fit want £420 to change it!! All that's gone is the flexible bit, the cat is fine, and I was wondering if there is a cheaper alternative possible, such as cutting out the flexi bit and welding in a solid pipe...
  20. Saab News
    http://www.autoevolution.com/news/sweden-a...ions-28760.html
1-20 of 73 Results
Top