Search Results for ‘hose’

Hello all, my Cassidy II, a 6 cyl autobox developed a leak in the metal portion of the rear power steering hose, high pressure line (w/banjo bolt). I've got a ProParts Swed replacement en-route. Anyone done this? As is true for numerous parts on this, it's in a damnable place. WIS describes...

Hi all, my brake vacuum pipe from the servo has melted at the t piece and is in need of replacement. Have tried looking for the replacement (needle in a haystack part number 5056049) Any ideas for a permanent fix please would be appreciated. :thumbsup:

I am sending 3 photos as I do not know the sence of the "Valve"(?) and the tube going from outside to the valve and from there to the throttle.

2005 9-5 Arc. I broke a couple hose fittings: black fitting red fitting https://www.dropbox.com/s/cqoa391ag7jmeq3/Black%20Fitting.JPG?dl=0 https://www.dropbox.com/s/so2c2bbbfugqsge/Red%20fitting.JPG?dl=0 Can these be purchased? Thank you

Can someone tell me what the stock intercooler hose is for a 99 SAAB 9-3 SE and would it be interchangeable with a 9-5 SAAB?

Hi, I have a 1999 Saab 95 and just replaced the ABS module. I noticed that there is a hose that is not connected to anything. The hose is clipped to the positive battery cable. Don't know if I broke it or it has been like that since I have had the car, about two years. photo is attached. Anyone...

I have a 99 SAAB 9-3 SE 4 door hatchback. I need to replace the Power steering hose, its the return hose from reservoir to rack. I'm having problems finding it at any parts stores. I was wondering if would be able to just buy the same kind of hose and use it in place of the original?

What does the wee lil valve do in the middle in front of the coolers/radiators tev's .... Ok it toggles it off & on .... But when & why ? :confused: Tid150 (Auto)

Hi folks, my 95 decided to eat the power steering hose that goes between the reservoir and the pump. Question is - can I replace it with a bit of generic hose or is that under high pressure. I know that there is a high and low pressure sides to PAS. It looks like a boggo hose to me, but I...

Can anyone please help me to source this Item. It Is the large diameter, very long hose that runs from the engine block and along the top of the radiator. Ours has split and is unserviceable. I can't photograph it as it was taken by my garage, who have drawn a blank trying to find one - they...

The hose clamp which holds the filling hose (rubber) to the plastic fuel tank is terribly corroded. Up to now I tried spraying anti rust, tried it with screw driver and other tools - in vain. :mad: :o I am afraid to approach with a saw due to the terrible connection rubber/plastic. Has...

Afternoon all, trying to get hold of bottom intercooler hose, 'u' shaped one that comes off bottom right of intercooler on a 2004 9-5 2.2tid. Please pm if you have one available, ta, Pox

Had my 9-3 serviced and the garage noticed the exhaust flex hose was split which seems legit as I noticed it was blowing a bit. Quoted me £900 (!!!!) to fix it as they said it is a single part that includes the catalytic converter. I was pretty dubious about that so brought it home and fired...

Hi, Im new to the forums and hoping someone can help me out, i blew the hose that runs from the head to water pump on a 2001 9.5 Aero, does anyone know where i can find a replacement, any help would be much appreciated

Hello, I have a 1996 900 my g/f mother wants me to replace the alternator on. I can tell it's gonna be a pretty big job. But, the only real question I have is about this plastic piece on the alternator the guy at the auto parts store called a hose. The one on the car does have this and I was...

Looking for hose marked #7 in pic

.

hi iv searched the net, googling for a clear, logical diagram for where all the hoses connect to from the throttle body. can someone please help me by uploading pics of where the vac hoses fit? my cars a 1999 saab 9-3 SE Thank you

HI Guys Bought some seafoam and want to use it on my 2.2TiD 2003 but what bloody vacuum hose do you disconnect to feed it in? Any help would be fab Si

Re: inlet hose I found out that the hose should be connected to the sensor on the end of the block. all sorted !!