Saabscene Saab Forum - Saab Technical Information Resource banner

Discussions Showcase Albums Media Media Comments Tags

1-20 of 62 Results
  1. New Saab 9-5 (2010 - on)
    I found a long standing leak in my 2.8 ltr. The leak is at the seal at the crankshaft seal. Seems bizarre that antifreeze leaks out of crankshaft. Anyone done it themselves?
  2. General Saab Discussions
    Today I was looking at the ignition system in the EPC and I stumbled across something called the crankshaft aperture disc, I've never heard of it before and I'm wondering what it is? and if it's Saab specific? I have the B205R if that's helpful. All help is appreciated, thanks.
  3. Saab 9-3 Sedan/Combi/TurboX/AWD(2003+)/Conv(2004+)
    Hi there my crankshaft pulley broke off so I was going to replace belt and pulley bit can't find any guides so if anyone has would be great! Thankyou.
  4. Help, Advice, Saabs and Motoring
    hi I recently did a head job and timing chain on my 1998 900 se. replaced front crank seal after running 1/2 hr blew seal out. seal doesn't fit all that tight but did require slight tapping in. i replaced seal with a little hardening permatex few days later drove car 1/2 hr seal leaking and...
  5. Help, Advice, Saabs and Motoring
    So I was replacing the o-ring and seal located at the oil pump behind the crankshaft pulley and a couple of bad things happen. First, I break part of the snap ring housing off, not the part boxed in red in pic but directly across it to the left. It's one of five metal pieces that actually hold...
  6. Saab 9-3 Sedan/Combi/TurboX/AWD(2003+)/Conv(2004+)
    Hello, I have a 2005 9-3 Aero Auto with a leaking front crankshaft seal. I have removed the drive belt and need to remove the crankshaft pulley (Harmonic Balancer). The crankshaft and the pulley keeps spinning, as does the bolt, as I try to remove it. Is there any method / tool that would...
  7. Saab 9-3 Sedan/Combi/TurboX/AWD(2003+)/Conv(2004+)
    Hello, I have a 2005 9-3 Aero B207 engine with Auto Box I am trying to replace the front crankshaft seal but find the Harmonic Balancer keeps spinning every time I try to loosen the bolt. Is there a specific tool to keep the Harmonic Balancer in place? Or a technique? I do not want to damage...
  8. Part number requests
    Hi, Im looking for the part number for the CPS, its for a 93 Aero 2.0 petrol 2008 manual Cheers
  9. Classic Saab 9-5 (1997 - 2009)
    Hello All -- Just been informed that the DMF on my 2006 1.9TiD 150bhp needs replacing (with the two-part clutch and slave cylinder!!) Is nothing ever easy? The quote is over £1150 There is mention of over £50 just for the bolts. Does anyone know just how many bolts there are and perhaps the Saab...
  10. Classic Saab 9-5 (1997 - 2009)
    I have a saab 95 2005 2 litre turbo does anyone know where I can buy a crankshaft sensor from ?
  11. Classic Saab 9-3/GM900 (1994 - 2002)/Conv ( -2003)
    Hello, i have a 2001 TId and the crankshaft pulley has broken. what sort of job is it to replace ? thanks
  12. Saab 9-3 Sedan/Combi/TurboX/AWD(2003+)/Conv(2004+)
    My CEL came on & the local garage diagnostic showed unidentified fault. The light switched off. When it lit again I went to Saab...they think it might be the Crankshaft position sensor but will take while to order new one. Is it safe to drive in meanwhile?
  13. Classic Saab 9-5 (1997 - 2009)
    I recently bought a 2000 Saab 9-5 with the V6Turbo engine. I came up to a stop light today and the engine cut out. It cranked and cranked and cranked and wouldn't start up. I let it sit there about 5 minutes, It started right up, studdered a little bit, then ran fine.After this incident the...
  14. Saab 9000 (1984 - 1998)
    Hey all, I am new to this forum, but have had my 9000 for 7 years. I am rebuilding the top end, and having trouble getting the center pulley/damper bolt off. Any tricks to be aware of? Also, anyone who has upgraded the camshafts from stock and has a thought on it, please comment. Thanks!! Scott
  15. Classic Saab 9-5 (1997 - 2009)
    any one know the size of this part? NG900, 9000 (94'-98'), 9-3 & 9-5 Crankshaft Seal (timing chain side)mines leaking like mad and my nearest autoparts shop is 60 miles away, who can't find it anyway, however the bearing and seal place will have it (so they say) if i can give them the sizes of...
  16. Classic Saab 9-3/GM900 (1994 - 2002)/Conv ( -2003)
    Hi all, following on from my previous 2 posts (Intermittant Starting Probs on 9-3 Aeor Coupe), I believe after doing lots of reasearch on this site that I am suffering from the Hot start Problem caused by a failing Crankshaft Position Sensor (although I am not experiencing any of the rough...
  17. Help, Advice, Saabs and Motoring
    Can anyone suggest how to find the crankshaft sensor on a 93 Aero (petrol, 2003)? I know it's supposed to be located towards the front of the engine block, but I've looked and looked and can't see where on earth it is. Do I need to remove anything first? Is it next to something that is...
  18. Saab 9-3 Sedan/Combi/TurboX/AWD(2003+)/Conv(2004+)
    Hi, Can anyone tell me if a special tool is needed to replace the rear crankshaft seal on my 2002 9-3 tdi?
  19. Saab 9-3 Sedan/Combi/TurboX/AWD(2003+)/Conv(2004+)
    Will engine be ok if crankshaft pulley wheel collasped? Seemed to sound fine,turned off straight away.
  20. Classic Saab 9-3/GM900 (1994 - 2002)/Conv ( -2003)
    Can anyone direct me to any drawings of photos of the position of the Crank Sensor on my 9-3 year 2000? How easy is it to change? Can it be reached from inside the bonnet? Thanks Patrick
1-20 of 62 Results