Search Results for ‘clip’

Ok, after surmising that the hardest part of doing this job would be getting to it, it's tucked in behind the brake vacuum servo on RHD models, I thought I'd feel around for the hard line retaining clip. (at the front of the cylinder in engine bay) Well Ive just poked around with various sized...

I need the part number for the rear window clip that goes on the window regulator? for a 99 9-3 SE hatchback. It looks like it's two parts being one metal and one plastic? I need the plastic part.

Yet again I have had my drivers side wing mirror taken off. The cover is ok, mirror gone for a Burton and so has the metal clip. Where can I get another? Anyone have the part number? Thanks

Hi all, I am replacing a damaged side skirt on my 56 plate 9-3 Vector Sport. The side skirt is held in place on the underside of the car with retainers, which appear to be plastic 'rivets' with centre pins. You seem to remove the clip by pushing in the centre pin and prising out the rivet. I...

About to change the pads and discs on my 04 9-3 Aero. Anyone got any tips on removing the clip on the caliper (Square design). I had a wee play with it when investigating the pads and i couldnt get it shifted. Hopefully someone here has a little experience and can offer some guidence. Thanks in...

Was pulling apart said Aero chasing a small water leak and thought I would check the tightness of everything that was visible. Guess what, the clamp to the turbo air pump was loose. Pulled it all down, cleaned it all up and nipped everything up nicely. Test drive. Wow! It went absolutely mental...

Hi all, I'm a newbie to the forum so please go easy on me. I'm looking for some help after hours of searching the web and found this forum so hopefully someone can point me in the right direction. I have a 9-3 Sports Saloon 2003 plate - I was driving down the road around 40mph and some kids...

Hi, Hello all, just joined! 1999 9-5 2.3 EcoPower, 140k miles, 50k since I bought her, no problems apart from a puff of smoke on start-up (that's not getting any worse) Until......clutch slave failed on the way to an interview....... subframe out, transmission out, new slave cylinder and...

Just a quick question. I've lost all boost (massively depressing!) a few times due to the wastegate actuator rod coming adrift on my 9000T (1988 2.0 FPT) - for now I've attempted to bodge it with a bit of stout wire but it's not really good enough and I don't want it going again on the next...

Ive just found out the retaining clip for the adjuster on the replacment caliper i got from euro parts is missing . How essential is this part ? Will the screw-in cover-cap hold the adjuster in place ?

Amongst the various other bits of car-related angst I've had recently, the wastegate arm and the solenoid rod have parted company on my 1994 2.3t. Couple of questions - firstly, is it an ordinary circlip, and secondly, if so, what size? Is there a part number or standard source of these? TIA.

I have just fitted a Brodit Pro Clip to my car and now want to buy a holder for my telephone a Sony Ericsson W800i. I seem to be totally baffled by the options but I do want to leave it so I can swap between the phone and the Brodit mount for the Tomtom 910 when it comes out (fingers crossed...

Facinating clip of 900's being made at the Malmo plant in 1989. Malmo plant making 900's in 1989.

About a year ago I stripped down my Aero engine, and although I took many photos there are 4 metal clips that I cannot place. They are about 2cm by 2cm with only 3 sides and with a hole of about 1cm dia. in the middle. They are to do with something connected to or close to the inlet manifold...

About a year ago I stripped down my Aero engine, and although I took many photos there are 4 metal clips that I cannot place. They are about 2cm by 2cm with only 3 sides and with a hole of about 1cm dia. in the middle. They are to do with something connected to or close to the inlet manifold...