Search Results for ‘camshaft’

Trying to see if this sprocket which powers the vacuum pump on the end of the cam shaft is the same as a 9 3 1.9 tid? It shows as a 9 5 part?

Hi took off the heads, tried to align the camshaft exactly where they came off. Put on the new timing belt and engine won't rotate past 90 degrees just stops. Engine is at top dead center. Took off belt engine rotates normally. I have pictures of the camshafts as they came off and tried to...

Unable to locate the timing mark on the engine casing on my 9-3 ?? Am I missing something maybe? Thanks

Will this tool work on a Saab 9-3 2.0turbo 2004 reg. I have the b207l engine

I have a 2005 SAAB 900 9-5 4cyl. I have replaced the crankshaft and have no spark. Please can anyone tell me where the camshaft sensor is. Is it in the ignition coil pack? some one mentioned it may be in the distributor, thanks Sharron

Hi there im looking for some advice. I bought a 2007 9-3 vectorsport 1.9 td about 2 months ago,with 60,000 miles on the clock, ran like a dream. It started juddering just after starting, then after a few days would not start. we took it to a garage( who we trust) they looked at the car and...

16v 1.9 tid 93 2007 Changing the Timing belt and water pump, Put on my own marks, and all seemed well until whilst Replacing the pump, I got distracted and Turned the camshaft pulley, Not sure how times around. I have lined it the marks up but as the Pump, the drive shaft and the camshaft...

Hi All after fixing vacuum leaks, injector and a bad connection between manifold and cat we have found one of the lobes on the camshaft is non existant. After searching around im struggling to find a camshaft online for a saab 93 2006 tid z19dt engine. any suggestions or part numbers for this...

Just changed my injector seals. Took the camshaft out instead of just tilting it. Had a couple of screwdrivers through the camshaft sprocket holes and had the chain cable tied to the sprocket. I think taking the vary tight sprocket bolt out the chain may had jumped a tooth. After finishing the...

Hi all - it's actually for my 9-3 but it looks the same on my 9000. What is the official name for the washer that plugs into the rear of the camshaft rocker cover - ie the one that the inlet breather plugs into. Mine has perished and I need a new one. Regards Jim

Hello, Newbee on these forums so please excuse me. I have searched the forum for similar problems that i'm experiencing with my 2006 saab 93 sportwagon but can’t find a similar. Problem: Car won’t turn over and a horrible whirring noise is heard when key is turned. Description: Past...

When investigating the cam followers on my T16 engine I managed to break one of the hollow camshaft inner bearing cap bolts :mad: (the inner ones next to the spark plugs that are hollow for oil to go through). I was wondering if anyone had a broken T16 engine and so some spare bolts? Also, I...

Check eng. lt. came on and scanner said cam pos. sens. fault P0340. Cleared it and its still off ?. Maybe loose connector ? KB

At the weekend I had the camshaft cover off to check the head bolts (following the recent thread). I then discovered that all of the bearing cap bolts on one of the camshafts had worked loose to some extent, with two bolts actually fully undone! Oddly enough I had thought the top end sounded...

I seem to be missing a seal and plug from the end of the camshaft,does this affect anything does anyone know as ive just looked it up in the parts cat and realized they are missing from my car. where do i get them from and what affect is it having without them?

After reading most searches I still cannot fathom out where my noise is coming from. It's a ticking with a metallic rattle that varies slightly, it also increases with revs. It's not the injecotors, chains are new, mileage is 194K so I'm suspecting either worn camshfts or cam followers...

After reading most searches I still cannot fathom out where my noise is coming from. It's a ticking with a metallic rattle that varies slightly, it also increases with revs. It's not the injecotors, chains are new, mileage is 194K so I'm suspecting either worn camshfts or cam followers...

Hi! Maybe somebody has inforomation from where could be found the drawings which show the difference the v4 camshaft lobe shapes (the standard, "7.2", "7.6" and "8.3")? the best link i have got so far: http://www.vsaab.com/SportRally/TOC.htm but this is not detailed enough...

Does anybody have any camshaft specifications for the 99/900 H series engines and any specs for a 'tuned' camshaft for the same engine, non-turbo.