Search Results for ‘actuator’

Hi, newbie here with a 95 Aero Turbo4 (in the UK). Having the engine stripped down to have a CAM Actuator Sensor issue investigated. I thought having a chain cam engine I wasn't in for any big engine problems. Does anyone know what the following code on my servicing dealer's work sheet might...

I have had some problems with my car (2001 2.0T HOT Aero 205bhp) recently but as she only has 102k and is in good condition I wanted to keep it. So I had the head gasket done 1000 miles ago and 2 weeks ago the Aircon pump ceased taking out the tensioners when the belt went. So after two big...

hi my swirl flap has come off and n0 3 does not move either way when accelerator pressed no4 just spins and leaks am I looking at a new manifold ? or removal and blank code p1109 showing but motor running pretty good bit slow at low revs ok otherwise, would it be ok to leave as is or will it get...

hi guys, the drivers door on my parents facelift 9-3 won't open from the outside, it will open from the inside however. What do you think the problem may be? I was thinking maybe broken door lock actuator Thanks Aaron

So i have been through quite a bit with my 1995 saab 9000 aero. I recently replaced the turbo and am waiting for the forge WGA. The question is this. If I drive super carefully, i.e dont spike the turbo, can I actually drive the car without damaging the engine or turbo? I have to go to a funeral...

Can I buy a new hydraulic actuator for 04 Saab 9-3 convertible? Where ? and what is the part number? Or must I send it off to be repaired ? And where for the that too?!?

Hey Saab lovers! My new to me 2004 Saab 9-3 convertible has a bad hydraulic actuator on the convertible over passenger head area. My 2 day old car let green slime out all over my passenger seat as I closed the roof . :( since Saab is not longer able to sell parts I am told that a company on the...

How do, Will an upgraded actuator give me quicker spool up ?? Can I increase this slightly on the orig aero one ?? Dawes valve gave effect but car felt too alien, not right, fluctuating revs etc, so have removed but miss the spool up.. Its mapped to 287 but still doesnt feel quick unless its at...

Hello Saab users I've got for sale an Inlet Manifold and a Swirl Actuator. Both are brand new. I bought them in December for my car but it turned out they were not required for a fix. Inlet manifold part number is 55210201. Swirl actuator part number is 55205127. They will fit Z19DTH engine...

Hi! The fuel door lock motor has crapped out on me. I need instructions in how to remove it. I have a 9-5 station wagon. I tried but I don't seem to be able to remove the black 'stash'-box on the right side in the trunk compartment (I logically suppose that's where I would access it from). I...

Hi i have a tdo4 turbo on my 2l 9-5 lpt from an aero that came from the breakers yard, along with some other mods it runs well but my question is how can you tell if the spring in the actuator is past it ? ie not holding boost long enough , do i need to fit a boost guage or just fit a stiffer...

Hi guys im new to this forum i have bought a saab 9-3 1.9 tid 150 vector sport 2005 it started when bringing her home black smoke cleaned out EGR valve which was replaced back in december 2011 and noticed swirl bar was off i bought new inlet manifold and actuator motor reinstalled by my mechanic...

Hi everyone, My latest battle is with the rear door actuator on my 2005 9-5. Basically all of the other doors lock / unlock correctly however the rear nearside does not, there's no noise from the actuator and the button doesn't go up or down automatically. I can lock and unlock the door...

Hi I need a turbo actuator valve for my 3.0 tid v6. It sits on the bulk head. It has two vacuum pipes attached to it. I have spoken to the dealer who tell me they can not supply me with one as Sweden does not have any. Can anyone advise where I can get a new or used one? Thanks in advance.

Hi there saab owners, What do you think about disconecting the actuator rod from nr.3 flap from the bottom of the inlet manifold by prising it off the ball joint and just leave it moving around disconected and fix all the flaps in open position? so the car will thing everithing is ok but the...

i dont know if anyone here has done this or not but it appears to be a fairly easy mod. basically the wastegate has an adjustment nut on the rod and allegedly loosening the nut and turning the end of the rod three turns clockwise can adjust base boost. i guess what im asking is if this mod is...

Hi Guys, I have a Saab 93 SS 2004 1.9 150bhp and i'm looking to replace the swirl actuator as i'm getting P1109 faults. I managed to get the part for a cheap price so i thought id try replacing that first to see if that resolves the issue - i'm not experiencing power loss or anything - just...

I am trying to take the wastegate actuator off one car and fit it to mine, tried today but failed then ran out of time. I can see the pin at the end of the rod but couldn't prise it out, I got the bottom nut off the other end but couldn't get any spanners/sockets that I had onto the top nut as...

hi all im unsure how to bleed the system, im replacing the clutch actuator unit and all referance say bleed as u would any hydraulic clutch but its not like any other hydraulic clutch as there is no pedal, any help please.