1994 9000 CDE NT Project

  1. Welcome to Saabscene – General discussion forum for Saab

    Welcome to Saabscene - a website dedicated to all things Saab.

    You are currently viewing our forum as a guest, which gives you limited access to view most discussions and access our other features. By joining our community, at no cost, you will have access to post topics, communicate privately with other members (PM), respond to polls, upload content and access many other special features. Registration is free, fast and simple, Join Saabscene today!
     
Results 1 to 8 of 8

Thread: 1994 9000 CDE NT Project

  1. #1
    Saab Newbie
    Join Date
    Aug 2019
    Location
    NC, USA
    Posts
    15

    1994 9000 CDE NT Project


  2. Remove Advertisements
    SaabScene.com
    Advertisements
     

  3. #2
    Saab Newbie
    Join Date
    Aug 2019
    Location
    NC, USA
    Posts
    15

    Re: 1994 9000 CDE NT Project


  4. #3
    Saab Newbie
    Join Date
    Aug 2019
    Location
    NC, USA
    Posts
    15

    Re: 1994 9000 CDE NT Project


  5. #4
    Saab Newbie
    Join Date
    Aug 2019
    Location
    NC, USA
    Posts
    15

    Re: 1994 9000 CDE NT Project

    Almost ready for new muslin wire channels. What an improvement from what you see in the first video!



    Last edited by Ryengoth; 10-02-2019 at 04:53 PM.

  6. #5
    Saab Newbie
    Join Date
    Aug 2019
    Location
    NC, USA
    Posts
    15

    Re: 1994 9000 CDE NT Project

    The rear seat pan is smuggling a beach.




    A little rust control is in order here. Brown satin rust-oleum will stop it. It's all surface rust, springs are in great shape.






  7. #6
    Saab Newbie
    Join Date
    Aug 2019
    Location
    NC, USA
    Posts
    15

    Re: 1994 9000 CDE NT Project

    Next up, trans drop and clutch repair. A much more solid and clean spot to work on the Saab too! Thanks Randy! CarolinaDyno
    Yes, I will probably end up putting it on the dyno when it's all done. I will be surprised if it can pull the roller.
    Oh. It will be getting an exterior wash and gas tank degreasing. From that old gas it smells like the neighbor's dog that never gets washed. And, it's right by the dyno bay. LOL Peeeeuuuuuu.


  8. #7
    Saab Newbie
    Join Date
    Aug 2019
    Location
    NC, USA
    Posts
    15

    Re: 1994 9000 CDE NT Project

    Rear seat foam is all cleaned up and dry. Cover needs the two mid bolster wire channels resewn and it'll be ready to re-install.



  9. #8
    Saab Newbie
    Join Date
    Aug 2019
    Location
    NC, USA
    Posts
    15

    Re: 1994 9000 CDE NT Project

    Not bad at all. I've seen worse. The caliper was reluctant to come off but the pads are extremely thick, lots of wear left. Lots of surface corrosion. The shift selector rod connector has extremely rusted hardware and I couldn't get to it to finish the transmission removal last weekend. I will put the transmission in 4th and that should move it far enough away from the power steering lines to let me reach the rubber connector and split it.








  10. Remove Advertisements
    SaabScene.com
    Advertisements
     

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Powered by vBadvanced CMPS v4.1.2