Search Results - Saabscene :: Saab Forum - Saab Technical Information Resource

Search:

Type: Posts; User: wildboar

Search: Search took 0.01 seconds.

  1. Replies
    2
    Views
    5,662

    Re: 2004 9-3 Audio upgrade to 6-disc CD

    Hello..you can install the Entertainment Head Unit - EHU and marry it with TECH2 to your car...you will be required Security Access..if you have TIS2000 or TISWeb..that would be piece of cake!..the...
  2. Replies
    4
    Views
    3,324

    I had the same problem with my car. The culprit...

    I had the same problem with my car. The culprit was the belt tensioner was deformed and the belt was off one groove in the air on the tensioner pulley.
    Was difficult to find but after installing a...
  3. Replies
    8
    Views
    3,648

    Re: saab 93 yr2001 auto

    Regarding your communication problem make sure TECH2 is well connected to OBD Port, check the pins are in-place and no loose wires from behind OBD Port, I have had cars with a loose wires that are...
  4. Replies
    8
    Views
    3,648

    Re: saab 93 yr2001 auto

    Hello,
    I have same car...first thing to do is to drain and fill your transmission at least 3 times until ATF comes super clean..drive around 50 to 100 km in between drains. DO NOT FLUSH the...
  5. Replies
    8
    Views
    2,594

    Re: Steering lock failure help please

    The switch is ISM - stands for Ignition Switch Module...sometimes this triggers the failure, to know for sure you need to have your car scanned with TECH2 - the codes will tell what is going on...on...
  6. Replies
    4
    Views
    6,828

    Re: Locked ignition switch Saab 93/YS3D

    Hello,
    This problem is a classic STARTER failure...you need to remove the starter and take it to an Electric Auto Shop and have it serviced, usually the problem is that starter motor ran out of...
  7. Re: 2008 93 1.8T Linear Auto Petrol heavier steering than Diesel

    The steering is soft in petrol cars as well. never driven diesel as they did not sell here in Mexico City, but all cars that I have serviced which have a heavy steering is due to improper maintenance...
  8. Replies
    1
    Views
    609

    Re: Passenger front floor wet

    The only way for water to get into that location is from the filter box, you changed the seal already, double check the seal was put correctly, remove the box and clean thoroughly, the drains in that...
  9. Replies
    11
    Views
    1,695

    Re: 9-3 ECU stolen - car about to be scrapped

    No problem with two VIN numbers that is normal..the TECH2 shows your original VIN plus the new ECM's VIN which is different from your car's...the VIN number can be easily changed with...
  10. Replies
    11
    Views
    1,695

    Hello. I can help you to resolve the problem....

    Hello.
    I can help you to resolve the problem.
    You need to make sure that the ECM that you bought is good. TECH2 should be able to marry it to your car after getting security access in TIS2000. If...
  11. Replies
    3
    Views
    2,563

    Re: security number

    The security code is 4 digit...and is located in EEPROM 93LC66A on the CIM board, needs to be removed carefully from the board and set in EEPROM reader and the file passed thru editor software to...
  12. Replies
    7
    Views
    2,592

    Re: I really am flummoxed with OP-COM

    I have OP-COM and it works fine..read and erase all failure codes, only problem is that I do not have the Security Code os my SAAB 93 2004...I am visisting a dealer in México City to try to get a...
  13. Thread: CAR PASS

    by wildboar
    Replies
    11
    Views
    13,943

    Re: CAR PASS

    Hello Philz55,
    I am using an OP-COM China Clone V 1.45 and have access to my SAAB, but when I try to enter some functions the software asks for a CAR-PASS Code, as I have read this doc was not used...
  14. Replies
    11
    Views
    24,067

    Re: Engine Mount replacement

    Hello ....thanks for sharing your experience with us...
    I have purchased the 4 mounts RHS and LHS and the Torque Bushings that go ubder the engine (are those the ones reffered and Front and Rear?)....
  15. Re: engine mount under batt any idea if hard to replace

    Seems that I have the same problem now..but my mounts are OK....the problem is located in the Strut mounts that are gone...I had my shocks replaced but due to error from Speed Racing.com I was unable...
Results 1 to 15 of 15
Powered by vBadvanced CMPS v4.1.2